Wall box 9206 for secure mounting and protection of the portable emergency body shower 8140.
- Dimensions (H x W x D): 700 x 330 x 263 mm
- Weight: 5.5 kg
Model 7260 AXION wall mounted eye and face wash features the medically acclaimed AXION MSR eye/face wash head assembly (patent pending). This revolutionary inverted flow design is the only product on the market that provides a Medically Superior Response consistent with all EMT, emergency room and doctors’ office protocols by sweeping contaminants away from the vulnerable nasal cavity. Traditional eyewashes irrigate from the outside edge of the eye back toward the nose, where contaminants can then be flushed into the nasal cavity through the lacrimal punctum, nature’s ocular cavity drain.
- Eyewash streams provide Zero Vertical Velocityâ„¢ stream engineering with even laminar flow for enhanced comfort, stability and effectiveness
- Unit features a round 11″ (27.9 cm) green ABS plastic receptor and aluminum
- Includes a mesh in-line strainer to collect line debris, and ball valve with stainless steel ball and stem for durability
- Supply: 1/2″ NPT. Waste: 1- 1/4″ NPT
- ANSI Z358.1 tempering solutions
- EN 15154 compliant
Certified by CSA to meet the ANSI Z358.1 Standard for Emergency Eyewash and Shower Equipment.
7603T240H – 240V Portable Air-Pressurized Tempered Emergency Eyewash (HazLoc)The Haws 7603T240H is an ideal, cost-efficient solution for a facility’s ANSI eyewash requirements in locations without access to a continuous potable water source. The pressurized 56.8 liter portable hazardous location eyewash uses a NEMA 4 heated, insulated blanket to provide ANSI compliant tempered water in operating temperatures between -30° C and 38° C for locations without access to a continuous potable water source.
- Features a 56.8 liter stainless steel tank
- Upgraded ball valves with stainless steel ball and stem
- Protective measures include: air pressure gauge, pressure relief valve, and tire-type air fill valve
- Measurements: 100.3 cm high, 40.6 cm diameter
- 240VAC, 50/60Hz, 0.64A electrical requirement
- Power cord not provided – power connection must be made according to code using Class I Division 2 compliant equipment
- CSA certified for NEMA/Type 4 in Class 1, Division 2, Group B, C, D, T6, and Class 2, Division 2, Group F, G locations; and to ANSI/ISEA Z358.1
The Haws 7603T240 is an ideal, cost-efficient solution for a facility’s ANSI eyewash requirements in locations without access to a continuous potable water source. The pressurized 15 gallon (56.8 L) portable eyewash uses a NEMA 4 heated, insulated blanket to provide ANSI compliant tempered water in operating temperatures between -30° C and 38° C for locations without access to a continuous portable water source.
- Features a 56.8 liter stainless steel tank
- Upgraded ball valves with stainless steel ball and stem
- Protective measures include: air pressure gauge, pressure relief valve, and tire-type air fill valve
- Measurements: 100.3 cm high, 40.6 cm diameter
- 240VAC, 50/60Hz, 0.64A electrical requirement
- CSA certified for NEMA/Type 4 in ordinary locations, and to ANSI/ISEA Z358.1
Model TWBS.EW.H An on-demand, prepackaged, fully engineered and tested tempering system to provide tempered water instantaneously. System is designed to increase cold water temperature by a minimum of 19° C at 15.1 L flow and 38° C at 7.5 L; thus it is suitable for single eyewash application. Outlet water temperature is factory set at 26° C.
- It is ideal for areas where supply water temperatures fall below 15° C while hot water is not present
- System consists of an 20 KW electrical instantaneous water heater, a hot shutoff valve, a bypass valve, an in-line 50 x 50 mesh filter, and an outlet temperature gauge
- Requires 3 – 6 ATM flowing pressure
- Inlet and Outlet: 1/2″ IPS.
- Electrical Supply: 480 VAC, 3-phase, 3 wire and ground. 24 amp per phase (optional 208/240 3-phase available – ask for quote).
- UL listed for indoor use only.
Model TWBS.EWE, lead-free Emergency Valve (patent pending) thermostatically mixes hot and cold water to provide a safe fluid supply for emergency eyewash equipment. The valve contains a secondary high temperature limit valve to provide additional protection to the user in the event of main tempering valve malfunction. Additionally, to ensure a fail-safe water supply for emergency shower and eyewash stations, a series of cold water by-pass valves open in the event of hot water pressure loss. (No gauges supplied – ASSE 1071 standard recommends gauges be placed 5 to 8 feet (1.52 to 2.44 m) downstream for the most accurate temperature measurement.)
- A flow rate of 1 to 12 gpm (3.8 to 45.4 L) for better temperature control across the operating range
- AXION’s superior design and technology provide a complete safety solution for increased victim comfort.
- Lowest internal pressure drop for this class of valve (advantage where supply pressure is low)
- Wax based thermostat technology for fast response time with proven highly reliable temperature control
- Highest Cold Water Bypass flow rate in the industry (83% of rated tepid flow rate)
- Modular lead-free brass design with internal check stops
- Over-sized valve seats resist failures caused by foreign matter
- A new and efficient shuttle design eliminates valve binding
- A custom funnel design improves temperature control at low flow rates
- Outlet temperature is factory set to 85® F (29® C)
- Tempered water: High temperature limit is factory set to 87® F (30® C)
- Cold water by-pass valves are closed during normal operation, regardless of flow rate
Listings: ASSE 1071, CSA B125.3, NSF/ANSI 372, NSF/ANSI 61-section 8, California Health and Safety Code 116875 (AB 1953).
TWBS.HF – Thermostatic Mixing ValveModel TWBS.HF, lead-free Emergency Valve (patent pending), thermostatically mixes hot and cold water to provide a safe fluid supply for emergency shower and eyewash equipment. The valve contains a secondary high temperature limit valve to provide additional protection to the user in the event of main tempering valve malfunction. Additionally, to ensure a fail-safe water supply for emergency shower and eyewash stations, a pressure sensing diverter valve is provided that sends a pressure signal to open the cold water by-pass valve in the event of hot water pressure loss, main valve thermostat malfunction, or clogged cold water check-stop. (No gauges supplied – ASSE 1071 standard recommends gauges be placed 5 to 8 feet (1.52 to 2.44 m) downstream for the most accurate temperature measurement.)
- A flow rate of 1 to 78 gpm (295 L) for better temperature control across the operating range
- AXION’s superior design and technology provide a complete safety solution for increased victim comfort.
- Lowest internal pressure drop for this class of valve (advantage where supply pressure is low)
- Wax based thermostat technology for fast response time with proven highly reliable temperature control
- Highest Cold Water Bypass flow rate in the industry (100% of rated tepid flow rate)
- Modular lead-free brass design with internal check stops
- Over-sized valve seats resist failures caused by foreign matter
- A new and efficient shuttle design eliminates valve sticking
- A custom funnel design improves temperature control at low flow rates
- Outlet temperature is factory set to 85® F (29® C)
- Tempered water: High temperature limit is factory set to 87® F (30® C)
- Cold water by-pass valves are closed during normal operation, regardless of flow rate
Listings: ASSE 1071, CSA B125.3, NSF/ANSI 372, NSF/ANSI 61-section 8, California Health and Safety Code 116875 (AB 1953).
TWBS.SHE – Thermostatic Mixing ValveModel TWBS.SHE, lead-free Emergency Valve (patent pending), thermostatically mixes hot and cold water to provide a safe fluid supply for emergency shower and eyewash equipment. The valve contains a secondary high temperature limit valve to provide additional protection to the user in the event of main tempering valve malfunction. Additionally, to ensure a fail-safe water supply for emergency shower and eyewash stations, a series of cold water by-pass valves open in the event of hot water pressure loss. (No gauges supplied – ASSE 1071 standard recommends gauges be placed 5 to 8 feet (1.52 to 2.44 m) downstream for the most accurate temperature measurement.)
- A flow rate of 1 to 74 gpm (280 L) for better temperature control across the operating range
- AXION’s superior design and technology provide a complete safety solution for increased victim comfort.
- Lowest internal pressure drop for this class of valve (advantage where supply pressure is low)
- Wax based thermostat technology for fast response time with proven highly reliable temperature control
- Highest Cold Water Bypass flow rate in the industry (68% of rated tepid flow rate)
- Modular lead-free brass design with internal check stops
- Over-sized valve seats resist failures caused by foreign matter
- A new and efficient shuttle design eliminates valve binding
- A custom funnel design improves temperature control at low flow rates
- Outlet temperature is factory set to 85® F (29® C)
- Tempered water: High temperature limit is factory set to 87® F (30® C)
- Cold water by-pass valves are closed during normal operation, regardless of flow rate
Listings: ASSE 1071, CSA B125.3, NSF/ANSI 372, NSF/ANSI 61-section 8, California Health and Safety Code 116875 (AB 1953).
H1109.8 – Barrier-Free Chilled Wall Mount FountainModel H1109.8 barrier-free electric water cooler provides 8 gph (30.3 L) chilled water performance in an engineered stainless steel skin. and uses a patented stainless steel, push-button activated, valve assembly allowing for front access stream adjustment as well as cartridge and strainer access. Outfitted with such protective features as vandal-resistant bubbler head, waste strainer, and bottom plate, this electric water cooler is quick to discourage vandals.
- 100% lead-free waterways.
- 18 gauge Type 304 Stainless Steel construction and required specialized mounting frame offer a well constructed sturdy fountain
- Grille slots are designed to eliminate sharp edges and are backed with a foam filter to protect the fan motor and high displacement compressor from debris
- Maintenance is made easy with front access to valve adjustment and cartridge replacement
- Designed to run at a low energy usage, this water cooler and fountain are assured to have a long lasting life
- One piece rectangular bowl is designed for extra durability and maintenance ease.
- Beautiful satin finish resists stains and corrosion
Model H1109.8 meets all current Federal Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, and Section 9.
Note: Electric water coolers are not recommended or designed for outdoor applications or enclosed pool areas (chlorine). These conditions may void warranty.
H1117.8 – Barrier-free Chilled Dual Wall Mount FountainModel H1117.8 “Hi-Lo” electric water cooler provides 8 gph (30.3 L) chilled water performance in an engineered stainless steel skin, and uses a patented stainless steel, push-button activated, valve assembly allowing for front access stream adjustment as well as cartridge and strainer access. Outfitted with such protective features as vandal-resistant bubbler heads, waste strainer, and bottom plates, these electric water coolers are quick to discourage vandals.
- 100% Lead free waterways. 14 gauge Type 304 Stainless Steel construction and required specialized mounting frame offer a well constructed sturdy fountain
- Maintenance is made easy with front access to valve adjustment and cartridge replacement
- Grille slots are designed to eliminate sharp edges and are backed with a foam filter to protect the fan motor and high displacement compressor from debris
- Designed to run at a low energy usage, this water cooler is assured to have a long lasting life
- One piece rectangular bowl is designed for extra durability and maintenance ease
- Beautiful satin finish resists stains and corrosion
Model H1117.8 meets all current Federal and Child ADA. Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, and Section 9.
Note: Electric water coolers are not recommended or designed for outdoor applications or enclosed pool areas (chlorine). These conditions may void warranty.
H1119.8 – Barrier-Free Chilled Dual Wall Mount FountainModel H1119.8 “Hi-Lo” barrier-free electric drinking fountain provides 8 gph (30.3 L) chilled water performance in an engineered stainless steel skin, and uses patented stainless steel, push-button activated, valve assemblies allowing for front access stream adjustment as well as cartridge and strainer access. Outfitted with such protective features as vandal-resistant bubbler heads, waste strainer, and bottom plates, these electric water coolers are quick to discourage vandals.
- 100% lead-free waterways.
- 18 gauge Type 304 Stainless Steel construction and required specialized mounting frame offer a well constructed sturdy fountain
- Maintenance is made easy with front access to valve adjustment and cartridge replacement
- Grille slots are designed to eliminate sharp edges and are backed with a foam filter to protect the fan motor and high displacement compressor from debris
- Designed to run at a low energy usage, this water cooler is assured to have a long lasting life
- One piece rectangular bowl is designed for extra durability and maintenance ease
- Beautiful satin finish resists stains and corrosion
Model H1119.8 meets all current Federal Hawsmanufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, and Section 9.
Note: Electric water coolers are not recommended or designed for outdoor applications or enclosed pool areas (chlorine). These conditions may void warranty.
HCR8.50 – Remote ChillerModel HCR8.50 is a 220 Volt, 50 Hz remote chiller provides 8.0 gallons (30.3 L) per hour of cold water. This remote can provide chilled water to a water to a wide variety of fountains with modern styling. Chiller can be concealed under a counter, between or within walls (check local codes), or high on a wall or column. Ideally suited for factories, cafeterias, restaurants, schools, and offices. Other uses could be for precooling for beverage dispensers and fountains, machine coolant cooling, photo and X-ray processing, laboratory experimental work, or a capacity booster for ice cube makers. Model HCR8.50, 8-gph remote chiller, includes a heavy gauge galvanized steel cabinet.
The refrigeration system is balanced to provide low energy usage and a longer life assured by utilizing a high displacement compressor, a counterflow cooling evaporator/chiller, efficient capillary sizing, a large capacity dryer-strainer, and a fan-cooled condenser with maximum heat exchange. Environmentally friendly R134a refrigerant is controlled by calibrated capillary tube. Air cooled remote chillers require air circulation for proper operation. Any chiller mounted under a counter must also be provided with adequate ventilation.
When chiller is installed in wall be certain that it can always be removed through opening without damaging either chiller or wall. Allow minimum 1″ clearance. Minimum 4″ clearance on back side. Unit is furnished with leads enclosed inside terminal enclosure 220 Volt, 50 Hz, single phase. Capacity is based on ARI standard of rating conditions of 50® F (10® C) drinking water, 80® F (26® C) inlet water, and 90® F (32® C) room temperature.
Multiple-Outlets: HCR8.50 is capable of supplying a maximum of 2 stations (bubbler, glassfiller). Supply line to station should be adequately insulated and no farther than 7 feet (2.12 m) from chiller.
Note: Electric water coolers are not recommended or designed for outdoor applications or enclosed pool areas (chlorine). These conditions may void warranty.