Haws 8904 AXION deck mounted eye/face wash features the medically acclaimed AXION MSR eye/face wash head assembly (patent pending). This revolutionary inverted flow design is the only product on the market that provides a Medically Superior Response consistent with all EMT, emergency room and doctors’ office protocols by sweeping contaminants away from the vulnerable nasal cavity. Traditional eyewashes irrigate from the outside edge of the eye back toward the nose, where contaminants can then be flushed into the nasal cavity through the lacrimal punctum, nature’s ocular cavity drain. Unit is activated with simple squeeze lever operation.
- Dust cover allows for the 8904 AXION to stay protected from debris when not in use
- Easily detected and maintained, emergency equipment is equipped with safety sign and test card to record weekly testing
- 8 foot (243.8 cm) green hose provides an extended coverage area to further optimize the irrigation process
- In order to comply with state codes the use of a vacuum breaker is required with all hand held eye/face wash body spray units (Haws offers model SP212)
Certified by CSA to meet the ANSI Z358.1 Standard for Emergency Eyewash and Shower Equipment.
7610 AXION – AXION® MSR Sink Mount Eye/Face WashLab units like the 7610 AXION barrier-free wall or deck mount pull down eye/face wash features the medically acclaimed AXION MSR eye/face wash head assembly (patent pending). This revolutionary inverted flow design is the only product on the market that provides a Medically Superior Response consistent with all EMT, emergency room and doctors’ office protocols by sweeping contaminants away from the vulnerable nasal cavity. Traditional eyewashes irrigate from the outside edge of the eye back toward the nose, where contaminants can then be flushed into the nasal cavity through the lacrimal punctum, nature’s ocular cavity drain.
- Unit can be deck or wall mounted with easy change-over instructions
- Extended-length pull down arms are designed to accommodate wheelchair access
- Eye/face wash streams provide Zero Vertical Velocityâ„¢ stream engineering with even laminar flow for enhanced comfort, stability and effectiveness
- Dust cover allows for the 7610 AXION to stay protected from debris when not in use
- Activation and deactivation occur at a 30 degree angle from horizontal limiting splash of water onto counter or wall
- Rear mount design allows the sink to remain open to other uses
- ANSI/ISEA Z358.1 tempering solutions
- EN 15154 compliant
Certified by CSA to meet the ANSI Z358.1 Standard for Emergency Eyewash and Shower Equipment.
7611 AXION – AXION® MSR Sink Mount Eye/Face WashLab units like the 7611 AXION swing-away eye/face wash features the medically acclaimed AXION MSR eye/face wash head assembly (patent pending). This revolutionary inverted flow design is the only product on the market that provides a Medically Superior Response consistent with all EMT, emergency room and doctors’ office protocols by sweeping contaminants away from the vulnerable nasal cavity. Traditional eyewashes irrigate from the outside edge of the eye back toward the nose, where contaminants can then be flushed into the nasal cavity through the lacrimal punctum, nature’s ocular cavity drain.
- Dust cover allows for the 7611 AXION to stay protected from debris when not in use
- Eyewash streams provide Zero Vertical Velocityâ„¢ stream engineering with even laminar flow for enhanced comfort, stability and effectiveness
- Requires minimal maintenance and is equipped with test card to record weekly testing
- Side mount design allows the unit to be mounted from either side of the sink to better fit numerous locations
- ANSI/ISEA Z358.1 tempering solutions
- EN 15154 compliant
Certified by CSA to meet the ANSI Z358.1 Standard for Emergency Eyewash and Shower Equipment
7612 AXION – AXION® MSR Sink Mount Eye/Face WashModel 7612 AXION sink or deck mounted eye/face wash features the medically acclaimed AXION MSR stainless steel eye/face wash head assembly (patent pending). This revolutionary inverted flow design is the only product on the market that provides a Medically Superior Response consistent with all EMT, emergency room and doctors’ office protocols by sweeping contaminants away from the vulnerable nasal cavity. Traditional eyewashes irrigate from the outside edge of the eye back toward the nose, where contaminants can then be flushed into the nasal cavity through the lacrimal punctum, nature’s ocular cavity drain. When not in use, this unit utilizes a swing-away feature so the area stays clear for everyday use.
- A Dust cover allows the 7612 AXION to stay protected from debris when not in use
- Requires minimal maintenance and is equipped with test card to record weekly testing
- Side mount design allows the unit to be mounted from the right side of the sink
- ANSI/ISEA Z358.1 tempering solutions
- EN 15154 compliant
Certified by CSA to meet the ANSI Z358.1 Standard for Emergency Eyewash and Shower Equipment
7612LH AXION – AXION® MSR Sink Mount Eye/Face WashModel 7612LH AXION sink or deck mounted eye/face wash features the medically acclaimed AXION MSR stainless steel eye/face wash head assembly (patent pending). This revolutionary inverted flow design is the only product on the market that provides a Medically Superior Response consistent with all EMT, emergency room and doctors’ office protocols by sweeping contaminants away from the vulnerable nasal cavity. Traditional eyewashes irrigate from the outside edge of the eye back toward the nose, where contaminants can then be flushed into the nasal cavity through the lacrimal punctum, nature’s ocular cavity drain. When not in use, this unit utilizes a swing-away feature so the area stays clear for everyday use.
- A dust cover allows the 7612LH AXION to stay protected from debris when not in use
- Requires minimal maintenance and is equipped with test card to record weekly testing
- Counter top mounted on the left side of a sink
- ANSI/ISEA Z358.1 tempering solutions
- EN 15154 compliant
Certified by CSA to meet the ANSI Z358.1 Standard for Emergency Eyewash and Shower Equipment
4210 – Deck SinkDeck mounted sink units like the 4210 are installed in accessible countertop locations for quick locating and convenient operation. Sunken down sink design helps to minimize excess splashing and self-rimming feature allows for easy mounting.
- Stainless steel construction offers a good amount of durability and corrosion resistance
- Beautiful satin finish resists stains and corrosion
- Sitting water-tight along with sound deadening underneath keep this unit mounted securely on any countertop
- Measurements are 25″ x 17″ x 5″ (63.5 x 43.2 x 12.7 cm)
- Mounted at the correct height and equipped with proper drinking fountain and faucet, this unit complies with requirements for drinking fountains
Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, and Section 9.
Specify one of the following gooseneck faucets to be installed left rear side:
Model 5510LF stay-open lever handle, polished chrome-plated brass gooseneck faucet,
Model 5452LF self-closing lever handle polished chrome-plated brass gooseneck faucet or,
Model 5530LF stay-open, hot and cold lever handle, polished chrome-plated brass gooseneck faucet.
Specify the following bubbler to be installed on right front side:
Model 5054LF lever handle polished chrome-plated brass drinking faucet,
Model 5017LF push button polished chrome-plated brass drinking faucet with renewable cartridge and vandal resistant lock pin, or
Model 5051LF self-closing lever handle drinking faucet with a polished chrome-plated brass finish, adjustable stream flow, and vandal resistant lock pin.
4230 – Deck SinkDeck mounted sink units like the 4230 are installed in accessible countertop locations for quick locating and convenient operation. Sunken down sink design helps to minimize excess splashing and self-rimming feature allows for easy mounting.
- Stainless steel construction offers a good amount of durability and corrosion resistance
- Beautiful satin finish resists stains and corrosion
- Sitting water-tight along with sound deadening underneath keep this unit mounted securely on any countertop
- Measurements are 31″ x 19″ x 5″ (78.7 x 48.2 x 12.7 cm)
- Mounted at the correct height and equipped with proper drinking fountain and faucet, this unit complies with requirements for drinking fountains
Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, and Section 9.
Specify one of the following gooseneck faucets to be installed left rear side:
Model 5510LF stay-open lever handle, polished chrome-plated brass gooseneck faucet.
Model 5452LF self-closing lever handle polished chrome-plated brass gooseneck faucet or,
Model 5530LF stay-open, hot and cold lever handle, polished chrome-plated brass gooseneck faucet.
Specify the following bubbler to be installed on right front side:
Model 5054LF lever handle polished chrome-plated brass drinking faucet.
Model 5017LF push button polished chrome-plated brass drinking faucet with renewable cartridge and vandal resistant lock pin, or
Model 5051LF self-closing lever handle drinking faucet with a polished chrome-plated brass finish, adjustable stream flow, and vandal resistant lock pin.
5010.6427SS – Drinking FaucetModel 5010.6427SS push button bubbler valve is designed with an adjustable stream regulation and a shielded bubbler to provide an anti-squirt drinking stream. Unit is self contained and is constructed from stainless steel with a polished finish, making this bubbler valve resistant to corrosive materials, and is easy to keep clean.
- Bubbler head includes: socket flange locked to bubbler inlet, washers, and locknut
- Dimensions: Flange diameter is 2-1/8″ (5.4 cm), shank is 7/8″ (2.2 cm) diameter x 1-1/8″ (3.2 cm) long, and connection is a 3/8″ IPS inlet
- Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, and Section 9.
Model 5010SS push button bubbler valve is designed with an adjustable stream regulation and a shielded bubbler to provide an anti-squirt drinking stream. Constructed from stainless steel with a polished finish, this bubbler valve is resistant to corrosive materials and is easily kept clean.
- Dimensions: Bottom of base to top of bubbler is 3-3/8″ (8.6 cm), base diameter is 1-1/4″ (3.2 cm), and connection is a 3/8″ IPS inlet
- Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, and Section 9.
Model 5017LF drinking faucet is designed with a shielded bubbler and self-closing push button with adjustable stream regulation to provide an anti-squirt drinking stream. Unit is to be mounted from sink or counter top and is constructed from a lead-free polished chrome-plated brass, making this bubbler valve resistant to corrosive materials and easy to keep clean.
- Drinking faucet includes: basin shank, locking pin, and mounting hardware
- Dimensions: 2″ (5.1 cm) high forged brass bubbler head with a 1/2″ O.D. (1.3 cm) slip-joint inlet.
- Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, and Section 9.
Model 5051LF lever handle drinking faucet is designed with a shielded bubbler to provide an anti-squirt drinking stream. Unit is to be mounted from sink or counter top and is constructed from a lead-free polished chrome-plated brass, making this bubbler valve resistant to corrosive materials and easy too keep clean. Unit comes further equipped with vandal resistant pins to prevent the unit from turning.
- Dimensions: Bottom of flange to top is 6-1/2″ (16.5 cm); flange diameter is 2″ (5.1 cm)
- Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, and Section 9.
Model 5054LF drinking faucet is designed with a shielded bubbler and self-closing lever handle valve with pressure regulating flow control to provide an anti-squirt drinking stream. Unit is to be mounted from a sink or counter top and is constructed from lead-free polished chrome-plated brass, making this bubbler valve resistant to corrosive materials and easy too keep clean.
- Drinking faucet includes: basin shank, locking pins, and valve mounting hardware
- Dimensions: 2″ (5.1 cm) high forged brass bubbler head with a 1/2″ O.D. (1.3 cm) slip-joint inlet.
- Haws manufactures drinking fountains and electric water coolers to be lead-free by all known definitions including NSF/ANSI Standard 61, and Section 9.