Model SP65PD AXION MSR eye/face wash head, designed for the pulldown line of Haws safety equipment, with inverted flow design is the only product on the market that provides a Medically Superior Response consistent with all EMT, emergency room and doctors’ office protocols by sweeping contaminants away from the vulnerable nasal cavity. Traditional eyewashes irrigate from the outside edge of the eye back toward the nose, where contaminants can then be flushed into the nasal cavity through the lacrimal punctum, nature’s ocular cavity drains. The eyewash streams provide a smooth, even laminar flow for enhanced comfort, stability and effectiveness. (Not for use with freeze protected models)
SP65SS – AXION MSR Eye/face Wash HeadModel SP65SS AXION MSR stainless steel eye/face wash inverted flow design is the only product on the market that provides a Medically Superior Response consistent with all EMT, emergency room and doctors’ office protocols by sweeping contaminants away from the vulnerable nasal cavity. Traditional eyewashes irrigate from the outside edge of the eye back toward the nose, where contaminants can then be flushed into the nasal cavity through the lacrimal punctum, nature’s ocular cavity drains. The eyewash streams provide a smooth, even laminar flow for enhanced comfort, stability and effectiveness. (Not for use with freeze protected models)
SP75 – Floor FlangeModel SP75 is a 9″ (22.9 cm) diameter gray epoxy cast-iron floor flange and 1-1/4″ IPS hot-dipped glavanized tee. A foot treadle assembly can be used with this flange.
SP80 – Mounting BracketModel SP80 is a cast aluminum mounting bracket used with wall mounted eye and eye/face wash models.
SP829 AXION – AXION® MSR ShowerheadModel SP829 AXION AXION® MSR 10-5/8″ (27 cm) ABS green plastic drench showerhead delivers dispersed flow for uniform drenching. This new hydrodynamic design minimizes the strong physical pressure that drives the water to the outer rim making the distribution equal across the entire footprint of the flow. Better use of the water flowing through the shower makes it more effective while providing a more comfortable environment by breaking the streams of water into smaller individual droplets. Inlet 1″ NPT.
SP829HPS AXION – AXION® MSR ShowerheadModel SP829HPS AXION AXION® MSR 10-5/8″ (27 cm) polished stainless steel drench showerhead delivers dispersed flow for uniform drenching. This new hydrodynamic design minimizes the strong physical pressure that drives the water to the outer rim making the distribution equal across the entire footprint of the flow. Better use of the water flowing through the shower makes it more effective while providing a more comfortable environment by breaking the streams of water into smaller individual droplets. Inlet 1″ NPT.
SP829SS AXION – AXION® MSR ShowerheadModel SP829SS AXION AXION® MSR 10-5/8″ (27 cm) stainless steel drench showerhead delivers dispersed flow for uniform drenching. This new hydrodynamic design minimizes the strong physical pressure that drives the water to the outer rim making the distribution equal across the entire footprint of the flow. Better use of the water flowing through the shower makes it more effective while providing a more comfortable environment by breaking the streams of water into smaller individual droplets. Inlet 1″ NPT.
SP90 – Eyewash BowlModel SP90 11″ (27.9 cm) round stainless steel with No. 2L bright finish on exterior. Includes the rubber seat washer.
SP93 – Eyewash BowlModel SP93 is a Safety Green 11″ (27.9 cm) ABS plastic receptor resistant to damage from alkalies, salt solutions, oils and most acids. For use on most Eyewashes and Eye/Face Wash Stations series.
SP95 – Waste TrapModel SP95 is a satin chrome-plated brass trap and tailpiece, 1-1/4″ (3.2 cm) O.D. inlet x 1-1/2″ IPS outlet.
TWBS.EW.H – Instantaneous Water HeaterModel TWBS.EW.H An on-demand, prepackaged, fully engineered and tested tempering system to provide tempered water instantaneously. System is designed to increase cold water temperature by a minimum of 19° C at 15.1 L flow and 38° C at 7.5 L; thus it is suitable for single eyewash application. Outlet water temperature is factory set at 26° C.
- It is ideal for areas where supply water temperatures fall below 15° C while hot water is not present
- System consists of an 20 KW electrical instantaneous water heater, a hot shutoff valve, a bypass valve, an in-line 50 x 50 mesh filter, and an outlet temperature gauge
- Requires 3 – 6 ATM flowing pressure
- Inlet and Outlet: 1/2″ IPS.
- Electrical Supply: 480 VAC, 3-phase, 3 wire and ground. 24 amp per phase (optional 208/240 3-phase available – ask for quote).
- UL listed for indoor use only.
Model TWBS.EWE, lead-free Emergency Valve (patent pending) thermostatically mixes hot and cold water to provide a safe fluid supply for emergency eyewash equipment. The valve contains a secondary high temperature limit valve to provide additional protection to the user in the event of main tempering valve malfunction. Additionally, to ensure a fail-safe water supply for emergency shower and eyewash stations, a series of cold water by-pass valves open in the event of hot water pressure loss. (No gauges supplied – ASSE 1071 standard recommends gauges be placed 5 to 8 feet (1.52 to 2.44 m) downstream for the most accurate temperature measurement.)
- A flow rate of 1 to 12 gpm (3.8 to 45.4 L) for better temperature control across the operating range
- AXION’s superior design and technology provide a complete safety solution for increased victim comfort.
- Lowest internal pressure drop for this class of valve (advantage where supply pressure is low)
- Wax based thermostat technology for fast response time with proven highly reliable temperature control
- Highest Cold Water Bypass flow rate in the industry (83% of rated tepid flow rate)
- Modular lead-free brass design with internal check stops
- Over-sized valve seats resist failures caused by foreign matter
- A new and efficient shuttle design eliminates valve binding
- A custom funnel design improves temperature control at low flow rates
- Outlet temperature is factory set to 85® F (29® C)
- Tempered water: High temperature limit is factory set to 87® F (30® C)
- Cold water by-pass valves are closed during normal operation, regardless of flow rate
Listings: ASSE 1071, CSA B125.3, NSF/ANSI 372, NSF/ANSI 61-section 8, California Health and Safety Code 116875 (AB 1953).